Lost Vape UB Mini Coils (5 Pack)

The UB Mini coils are designed for the Orion Mini Pod.

Product Specifications:
UB Mini S1 Mesh Coil V1 Edition 0.8ohm 12-17W KA1 RDL/MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S2 Mesh Coil V1 Edition 1.0ohm 9-13W KA1 RDL/MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S3 Mesh Coil V1 Edition 0.6ohm 16-21W KA1 RDL/MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S4 Mesh Coil V1 Edition 1.2ohm 9-11W KA1 MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S5 Mesh Coil V1 Edition 1.4ohm 6-9W KA1 MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S1 Mesh Coil V2 Edition 0.8ohm 12-17W KA1 RDL/MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S2 Mesh Coil V2 Edition 1.0ohm 9-13W KA1 RDL/MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S3 Mesh Coil V2 Edition 0.6ohm 16-21W KA1 RDL/MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S4 Mesh Coil V2 Edition 1.2ohm 9-11W KA1 MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

UB Mini S5 Mesh Coil V2 Edition 1.4ohm 6-9W KA1 MTL (Launched with the Orion Mini Pod) - WATTAGE MODE ONLY

Compatibility:
Consult the Atomizers utilizing Lost Vape UB Mini Coils at the Atomizers Using The Same Coils Category

Are all of these coils, working with my compatible AIO Pod System?
Consult the Coil Specs per System Categories (Various Parts, you have to struggle a bit!)

* As with Pod Tanks, Sub-Ohm Tanks & MTL Tanks, the paired device dictates the Ohm Limit of your coils
Warning: DO NOT use such atomizers with Mechanical Mods or a hard short might occur which can result in the battery bursting.

How to prime your new coil:
New coils must ALWAYS be fully saturated before FIRST use, otherwise the cotton inside will be burned.
Hold the coil in your hand and drip not just a few drops of e-Liquid but the required amount (Dependent on the coils' size) directly into the top hole. Do this on an angle, so that the cotton on the inner wall absorbs the e-Liquid. Next, start dripping some e-Liquid into the holes on the sides of your coil. There may be 2 or more drops for each hole, and you’ll notice that the e-Liquid is quickly absorbed by the cotton. You’ll want to make sure that you keep dripping into these holes until it stops absorbing it. Install the coil into your atomizer, fill the latter with e-Liquid and take a couple of puffs but with your device off and your airflow open. Don’t inhale too hard. Just inhale as if you’re taking a normal draw. Your coil is fully saturated!

Comment:
Replacement Coils are almost always produced and sold by pack of 5 or pack of 4, of 3 or 2. Sometimes we hear of vendors selling them by the unit - please be aware of this. We do not recommend buying coils by the unit - from a hygiene standpoint - it forces the package to be opened and cut through the sealed packaging. Also when you buy coils by the unit you don't get the scratch-and-check authentication sticker that's on retail box!