Aspire Triton Coils (5 Pack)

Aspire Triton Coils are belonging to the Aspire Atlantis Coil Family

The Triton coils are designed for the Triton Sub-Ohm Tank.

Product Specifications:
Triton Coil 0.3ohm 55-65W SS316L DL (Launched with the Triton Sub-Ohm Tank) - WATTAGE MODE & TEMPERATURE CONTROL

Triton Coil 0.4ohm 25-30W SS316L RDL (Launched with the Triton Sub-Ohm Tank) - WATTAGE MODE & TEMPERATURE CONTROL

Triton Coil 1.8ohm 10-13W KA1 MTL (Launched with the Triton Sub-Ohm Tank) - WATTAGE MODE ONLY

Triton Clapton Coil 0.5ohm 40-45W KA1 DL (Launched with the Triton 2 Sub-Ohm Tank) - WATTAGE MODE ONLY

Triton Ni200 Coil 0.15ohm DTL (Launched with the Triton 2 Sub-Ohm Tank) - TEMPERATURE CONTROL ONLY

Compatibility:
Consult the Atomizers utilizing Aspire Atlantis Coil Family at the Atomizers Using The Same Coils Category

Are all of these coils, working with my compatible AIO Pod System?
Yes. Boro devices pairing them with the Billet Box A-Boro Tank (Bridge Coil Boro Pod) using the OEM Atlantis Bridge Coil Adapter

* As with Pod Tanks, Sub-Ohm Tanks & MTL Tanks, the paired device dictates the Ohm Limit of your coils
Warning: DO NOT use such atomizers with Mechanical Mods or a hard short might occur which can result in the battery bursting.

Warning: DO NOT use the Triton Ni200 Coil if your device does not support Nickel Mode/TCR Mode!

Please Note: Before using Sub-Ohm coils requiring high wattage you must ensure that your batteries can handle them safely.
Improper use can lead to damage or injury.

WARNING: It’s EXTREMELY important that you NEVER vape Ni200 or Ti1 coils in Wattage Mode. You might burn them and inhale some very TOXIC fumes. So be careful always and make sure that:
1. You have selected the proper TC Mode - i.e. Titanium Mode for Ti1 coils- when using TC Mode.
2. You have set the proper TCR value when using TCR Mode. If TCR value you set is higher than actual, you'll burn the coil(s).

How to prime your new coil:
New coils must ALWAYS be fully saturated before FIRST use, otherwise the cotton inside will be burned.
Hold the coil in your hand and drip not just a few drops of e-Liquid but the required amount (Dependent on the coils' size) directly into the top hole. Do this on an angle, so that the cotton on the inner wall absorbs the e-Liquid. Next, start dripping some e-Liquid into the holes on the sides of your coil. There may be 2 or more drops for each hole, and you’ll notice that the e-Liquid is quickly absorbed by the cotton. You’ll want to make sure that you keep dripping into these holes until it stops absorbing it. Install the coil into your atomizer, fill the latter with e-Liquid and take a couple of puffs but with your device off and your airflow open. Don’t inhale too hard. Just inhale as if you’re taking a normal draw. Your coil is fully saturated!

Comment:
Replacement Coils are almost always produced and sold by pack of 5 or pack of 4, of 3 or 2. Sometimes we hear of vendors selling them by the unit - please be aware of this. We do not recommend buying coils by the unit - from a hygiene standpoint - it forces the package to be opened and cut through the sealed packaging. Also when you buy coils by the unit you don't get the scratch-and-check authentication sticker that's on retail box!