Eleaf EC Coils (5 Pack)

0 Rating
13,50 €
SKU: VD-1461

Eleaf EC Coils are belonging to the Aspire Atlantis Coil Family

The EC coils are designed for various MELO Sub-Ohm Tanks, the iJust 2 Sub-Ohm Tank & can also be used with the Aspire Triton Sub-Ohm Tanks.

Product Specifications:
EC-2 Coil 0.3ohm 30-80W KA1 DL (Launched with the Melo 4 Sub-Ohm Tank) - WATTAGE MODE ONLY

EC-2 Coil 0.5ohm 30-100W KA1 DL (Launched with the Melo 4 Sub-Ohm Tank) - WATTAGE MODE ONLY

EC-M Multihole Mesh Coil 0.15ohm 30-75W KA1 DL (Launched with the Melo 4 Sub-Ohm Tank) - WATTAGE MODE ONLY

EC-N Net Mesh Coil 0.15ohm 30-70W KA1 DL (Launched with the Melo 4 Sub-Ohm Tank) - WATTAGE MODE ONLY

EC-S SS316 Mesh Coil 0.6ohm 15-30W SS316 RDL (Launched with the Melo 5 Sub-Ohm Tank) - WATTAGE MODE & TEMPERATURE CONTROL

EC-A Mesh Coil 0.3ohm 30-50W AST-Steel DL (Launched with the Melo 4S Sub-Ohm Tank) - WATTAGE MODE ONLY

EC-A Mesh Coil 0.5ohm 20-40W AST-Steel DL (Launched with the Melo 4S Sub-Ohm Tank) - WATTAGE MODE ONLY

EC-A Mesh Coil 0.15ohm 40-70W AST-Steel DL (Launched with the Melo 4S Sub-Ohm Tank) - WATTAGE MODE ONLY

EC2-M Mesh Coil 0.3ohm 30-50W KA1 DL (Launched with the Melo C Sub-Ohm Tank) - WATTAGE MODE ONLY

ECL Dual Coil 0.18ohm 50-80W DL SS316 (Launched with the Lemo 3 Sub-Ohm Tank) - WATTAGE MODE & TEMPERATURE CONTROL

ECML Mesh Coil 0.75ohm 8-25W MTL KA1 (Launched with the Lemo 3 Sub-Ohm Tank) - WATTAGE MODE ONLY

Compatibility:
Consult the Atomizers utilizing Aspire Atlantis Coil Family at the Atomizers Using The Same Coils Category

Are all of these coils, working with my compatible AIO Pod System?
Yes. Boro devices pairing them with the Billet Box A-Boro Tank (Bridge Coil Boro Pod) using the OEM Atlantis Bridge Coil Adapter

* As with Pod Tanks, Sub-Ohm Tanks & MTL Tanks, the paired device dictates the Ohm Limit of your coils
Warning: DO NOT use such atomizers with Mechanical Mods or a hard short might occur which can result in the battery bursting.

Please Note: Before using Sub-Ohm coils requiring high wattage you must ensure that your batteries can handle them safely.
Improper use can lead to damage or injury.

How to prime your new coil:
New coils must ALWAYS be fully saturated before FIRST use, otherwise the cotton inside will be burned.
Hold the coil in your hand and drip not just a few drops of e-Liquid but the required amount (Dependent on the coils' size) directly into the top hole. Do this on an angle, so that the cotton on the inner wall absorbs the e-Liquid. Next, start dripping some e-Liquid into the holes on the sides of your coil. There may be 2 or more drops for each hole, and you’ll notice that the e-Liquid is quickly absorbed by the cotton. You’ll want to make sure that you keep dripping into these holes until it stops absorbing it. Install the coil into your atomizer, fill the latter with e-Liquid and take a couple of puffs but with your device off and your airflow open. Don’t inhale too hard. Just inhale as if you’re taking a normal draw. Your coil is fully saturated!

Comment:
Replacement Coils are almost always produced and sold by pack of 5 or pack of 4, of 3 or 2. Sometimes we hear of vendors selling them by the unit - please be aware of this. We do not recommend buying coils by the unit - from a hygiene standpoint - it forces the package to be opened and cut through the sealed packaging. Also when you buy coils by the unit you don't get the scratch-and-check authentication sticker that's on retail box!

There are yet no reviews for this product.

Please log in to write a review. Log in