Eleaf HW Coils (Variant Packs)

Eleaf HW Coils are belonging to the SMOK TFV8 Baby Beast Coil Family

The HW coils are designed for various Eleaf Sub-Ohm Tanks.

Product Specifications:
HW-T Coil 0.2ohm 40-90W KA1 (Launched with the Rotor Sub-Ohm Tank) - WATTAGE MODE ONLY

HW-T2 Coil 0.2ohm 35-75W KA1 (Launched with the Rotor Sub-Ohm Tank) - WATTAGE MODE ONLY

HW1 Single Parallel Coil 0.2ohm 40-80W SS316L (Launched with the Ello Sub-Ohm Tank) - WATTAGE MODE & TEMPERATURE CONTROL

HW2 Dual Parallel Coil 0.3ohm 30-70W KA1 (Launched with the Ello Sub-Ohm Tank) - WATTAGE MODE ONLY

HW3 Triple Parallel Coil 0.2ohm 50-130W KA1 (Launched with the Ello Sub-Ohm Tank) - WATTAGE MODE ONLY

HW4 Quadruple Parallel Coil 0.3ohm 40-110W KA1 (Launched with the Ello Sub-Ohm Tank) - WATTAGE MODE ONLY

HW-N Net Coil 0.2ohm 50-130W KA1 (Launched with the Ello Duro Sub-Ohm Tank) - WATTAGE MODE ONLY

HW-N Dual Coil 0.25ohm 25-65W KA1 (Launched with the Ello Duro Sub-Ohm Tank) - WATTAGE MODE ONLY

HW-M Multi Hole Coil 0.15ohm 50-100W KA1 (Launched with the Ello Duro Sub-Ohm Tank) - WATTAGE MODE ONLY

HW-M Dual Coil 0.2ohm 25-60W KA1 (Launched with the Ello Duro Sub-Ohm Tank) - WATTAGE MODE ONLY

HW-N2 Net Coil 0.2ohm 40-90W KA1 (Launched with the Ello Pop Sub-Ohm Tank) - WATTAGE MODE ONLY

HW-M2 Multi Hole Coil 0.2ohm 40-90W KA1 (Launched with the Ello Pop Sub-Ohm Tank) - WATTAGE MODE ONLY

Compatibility:
Consult the Atomizers utilizing SMOK TFV8 Baby Beast Coil Family at the Atomizers Using The Same Coils Category

Are all of these coils, working with my compatible AIO Pod System?
Consult the Coil Specs per System Categories (Various Parts, you have to struggle a bit!)

* As with Pod Tanks, Sub-Ohm Tanks & MTL Tanks, the paired device dictates the Ohm Limit of your coils
Warning: DO NOT use such atomizers with Mechanical Mods or a hard short might occur which can result in the battery bursting.

Please Note: Before using Sub-Ohm coils requiring high wattage you must ensure that your batteries can handle them safely.
Improper use can lead to damage or injury.

How to prime your new coil:
New coils must ALWAYS be fully saturated before FIRST use, otherwise the cotton inside will be burned.
Hold the coil in your hand and drip not just a few drops of e-Liquid but the required amount (Dependent on the coils' size) directly into the top hole. Do this on an angle, so that the cotton on the inner wall absorbs the e-Liquid. Next, start dripping some e-Liquid into the holes on the sides of your coil. There may be 2 or more drops for each hole, and you’ll notice that the e-Liquid is quickly absorbed by the cotton. You’ll want to make sure that you keep dripping into these holes until it stops absorbing it. Install the coil into your atomizer, fill the latter with e-Liquid and take a couple of puffs but with your device off and your airflow open. Don’t inhale too hard. Just inhale as if you’re taking a normal draw. Your coil is fully saturated!

Comment:
Replacement Coils are almost always produced and sold by pack of 5 or pack of 4, of 3 or 2. Sometimes we hear of vendors selling them by the unit - please be aware of this. We do not recommend buying coils by the unit - from a hygiene standpoint - it forces the package to be opened and cut through the sealed packaging. Also when you buy coils by the unit you don't get the scratch-and-check authentication sticker that's on retail box!