Joyetech BF Coils (5 Pack)

The BF coils are designed for various Joyetech Vape Tanks, Sub-Ohm Tanks, AIO Box Mod Systems & AIO Vape Pen Systems.

Product Specifications:
BF SS316 0.5ohm 15-30W SS316L DL (Launched with the Cubis Vape Tank) - WATTAGE MODE & TEMPERATURE CONTROL

BF SS316 0.6ohm 10-28W SS316L MTL (Launched with the eGo AIO Vape Pen System) - WATTAGE MODE & TEMPERATURE CONTROL

BF SS316 1.0ohm 10-25W SS316L MTL (Launched with the Cubis Vape Tank) - WATTAGE MODE & TEMPERATURE CONTROL

BF Clapton 1.5ohm 8-20W KA1 MTL (Launched with the Cubis Vape Tank) - WATTAGE MODE ONLY

BF-Ni200 0.2ohm 500-550F Ni200 DL (Launched with the Cubis Vape Tank) - TEMPERATURE CONTROL ONLY

BF-Ti1 0.4ohm 450-500F Ti1 DL (Launched with the Cubis Vape Tank) - TEMPERATURE CONTROL ONLY

BFC Mesh Coil 0.8ohm 14-20W SS316L MTL/RDL (Launched with the eGo AIO² Vape Pen System) - WATTAGE MODE & TEMPERATURE CONTROL

Compatibility:
Consult the Atomizers utilizing Joyetech BF Coils at the Atomizers Using The Same Coils Category

Are all of these coils, working with my compatible AIO Vape Pen/Box Mod System?
Consult the Coil Specs per System Categories (Various Parts, you have to struggle a bit!)

* As with Pod Tanks, Sub-Ohm Tanks & MTL Tanks, the paired device dictates the Ohm Limit of your coils
Warning: DO NOT use such atomizers with Mechanical Mods or a hard short might occur which can result in the battery bursting.

WARNING: DO NOT use the Ni200/Ti1 Coils if your device does not support Nickel Mode/Ti Mode/TCR Mode!
It’s EXTREMELY important that you NEVER vape Ni200 or Ti1 coils in Wattage Mode. You might burn them and inhale some very TOXIC fumes. So be careful always and make sure that:
1. You have selected the proper TC Mode - i.e. Titanium Mode for Ti1 coils- when using TC Mode.
2. You have set the proper TCR value when using TCR Mode. If TCR value you set is higher than actual, you'll burn the coil(s).

Please Note: Before using Sub-Ohm coils requiring high wattage you must ensure that your batteries can handle them safely.
Improper use can lead to damage or injury.

How to prime your new coil:
New coils must ALWAYS be fully saturated before FIRST use, otherwise the cotton inside will be burned.
Hold the coil in your hand and drip not just a few drops of e-Liquid but the required amount (Dependent on the coils' size) directly into the top hole. Do this on an angle, so that the cotton on the inner wall absorbs the e-Liquid. Next, start dripping some e-Liquid into the holes on the sides of your coil. There may be 2 or more drops for each hole, and you’ll notice that the e-Liquid is quickly absorbed by the cotton. You’ll want to make sure that you keep dripping into these holes until it stops absorbing it. Install the coil into your atomizer, fill the latter with e-Liquid and take a couple of puffs but with your device off and your airflow open. Don’t inhale too hard. Just inhale as if you’re taking a normal draw. Your coil is fully saturated!

Comment:
Replacement Coils are almost always produced and sold by pack of 5 or pack of 4, of 3 or 2. Sometimes we hear of vendors selling them by the unit - please be aware of this. We do not recommend buying coils by the unit - from a hygiene standpoint - it forces the package to be opened and cut through the sealed packaging. Also when you buy coils by the unit you don't get the scratch-and-check authentication sticker that's on retail box!